View UPG2413T6Z_7819590.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

r09ds0001ej0100 rev.1.00 page 1 of 11 may 20, 2010 preliminary data sheet pg2413t6z gaas integrated circuit sp3t switch for bluetooth tm and 802.11b/g description the pg2413t6z is a gaas mmic sp3t switch which was developed for bluetooth, wireless lan. this device can operate at frequencies from 0.5 to 3.0 ghz, with low insertion loss. this device is housed in a 8-pin plastic tson (t hin s mall o ut-line flat n on-leaded) package and is suitable for high- density surface mounting. features ? switch control voltage : v cont (h) = 3.0 v typ., v cont (l) = 0 v typ. ? low insertion loss : l ins = 0.35 db typ. @ f = 1.0 ghz : l ins = 0.45 db typ. @ f = 2.0 ghz : l ins = 0.50 db typ. @ f = 2.5 ghz ? high isolation : isl = 26 db typ. @ f = 1.0 ghz : isl = 20 db typ. @ f = 2.0 ghz : isl = 18 db typ. @ f = 2.5 ghz ? handling power : p in (0.1 db) = +28.0 dbm typ. @ f = 2.5 ghz, v cont (h) = 3.0 v, v cont (l) = 0 v ? high-density surface mounting : 8- pin plastic tson package (1.5 1.5 0.37 mm) applications ? bluetooth and ieee802.11b/g etc. ordering information part number order number package marking supplying form pg2413t6z-e2 pg2413t6z-e2-a 8-pin plastic tson (pb-free) g6f ? embossed tape 8 mm wide ? pin 1, 8 face the perforation side of the tape ? qty 3 kpcs/reel remark to order evaluation samples, please contact your nearby sales office. part number for sample order: pg2413t6z caution although this device is designed to be as robust as possi ble, esd (electrostatic discharge) can damage this device. this device must be protected at all times from esd. static charges may eas ily produce potentials of several kilovolts on the human body or equipment, whic h can discharge without detection. industry-standard esd precautions must be employed at all times. r09ds0001ej0100 rev.1.00 may 20, 2010 free datasheet http:///
pg2413t6z r09ds0001ej0100 rev.1.00 page 2 of 11 may 20, 2010 pin connections and inte rnal block diagram pin no. pin name 1 rfc 2 gnd 3 v cont 1 4 rf1 5 rf2 6 v cont 2 7 v cont 3 (bottom view) 1 2 3 8 7 4 5 6 (top view) g6f (top view) rfc gnd v cont 1 rf1 rf2 rf3 v cont 3 v cont 2 8 7 6 1 2 5 4 3 8 7 6 1 2 5 4 3 8 rf3 remark exposed pad : gnd truth table v cont 1 v cont 2 v cont 3 rfc ? rf1 rfc ? rf2 rfc ? rf3 high low low on off off low high low off on off low low high off off on absolute maximum ratings (t a = +25 c, unless otherwise specified) parameter symbol ratings unit switch control voltage v cont +6.0 note v input power (v cont (h) = 1.8 v) p in +26 dbm input power (v cont (h) = 2.3 v) p in +28 dbm input power (v cont (h) = 3.0 v) p in +32 dbm input power (v cont (h) = 3.6 v) p in +34 dbm operating ambient temperature t a ? 45 to +85 c storage temperature t stg ? 55 to +150 c note: ? v cont (h) ? v cont (l) ? 6.0 v recommended operating range (t a = +25 c) parameter symbol min. typ. max. unit operating frequency f 0.5 ? 3.0 ghz switch control voltage (h) v cont (h) 1.8 3.0 3.6 v switch control voltage (l) v cont (l) ? 0.2 0 0.2 v control voltage difference (h) v cont (h) note1 ? 0.1 0 0.1 v control voltage difference (l) v cont (l) note2 ? 0.1 0 0.1 v notes: 1. v cont (h) is a difference between the maximum and the minimum control voltages among v cont 1 (h) , v cont 2 (h) and v cont 3 (h) . 2. v cont (l) is a difference between the maximum and the minimum control voltages among v cont 1 (l) , v cont 2 (l) and v cont 3 (l) . free datasheet http:///
pg2413t6z r09ds0001ej0100 rev.1.00 page 3 of 11 may 20, 2010 electrical characteristics 1 (t a = +25 c, v cont (h) = 3.0 v, v cont (l) = 0 v, z o = 50 , dc blocking capacitors = 56 pf, unless otherwise specified) parameter symbol pass test condi tions min. typ. max. unit insertion loss l ins rfc to rf1, 2, 3 f = 0.5 to 1.0 ghz ? 0.35 0.60 db f = 1.0 to 2.0 ghz ? 0.45 0.70 db f = 2.0 to 2.5 ghz ? 0.50 0.75 db f = 2.5 to 3.0 ghz ? 0.60 ? db isolation isl rfc to rf1, 2, 3 f = 0.5 to 1.0 ghz 23 26 ? db (off) f = 1.0 to 2.0 ghz 17 20 ? db f = 2.0 to 2.5 ghz 15 18 ? db f = 2.5 to 3.0 ghz ? 16 ? db return loss (rfc) rl c f = 0.5 to 3.0 ghz 15 20 ? db return loss (rf1, 2, 3) rl1, 2, 3 f = 0.5 to 3.0 ghz 15 20 ? db 0.1 db loss compression p in (0.1 db) rfc to rf1, 2, 3 f = 2.5 ghz +25.0 +28.0 ? dbm input power note 1 1 db loss compression input power note 2 p in (1 db) rfc to rf1, 2, 3 f = 2.5 ghz, v cont (h) = 2.3 v ? +27.0 ? dbm f = 2.5 ghz, v cont (h) = 3.0 v ? +31.0 ? dbm f = 2.5 ghz, v cont (h) = 3.6 v ? +33.0 ? dbm 2nd harmonics 2f0 f = 2.5 ghz, p in = 23 dbm ? 75 ? dbc 3rd harmonics 3f0 f = 2.5 ghz, p in = 23 dbm ? 75 ? dbc switch control current i cont no rf input ? 0.1 5.0 a switch control speed t sw 50% ctl to 90/10% rf ? 50 ? ns notes: 1. p in (0.1 db) is the measured input power level when the insert ion loss increases 0.1 db more than that of the linear range. 2. p in (1 db) is the measured input power level when the inserti on loss increases 1 db more than that of the linear range. caution it is necessary to use dc blocking capacitors with this device. free datasheet http:///
pg2413t6z r09ds0001ej0100 rev.1.00 page 4 of 11 may 20, 2010 electrical characteristics 2 (t a = +25 c, v cont (h) = 1.8 v, v cont (l) = 0 v, z o = 50 , dc blocking capacitors = 56 pf, unless otherwise specified) parameter symbol pass test condi tions min. typ. max. unit insertion loss l ins rfc to rf1, 2, 3 f = 0.5 to 1.0 ghz ? 0.35 0.65 db f = 1.0 to 2.0 ghz ? 0.45 0.75 db f = 2.0 to 2.5 ghz ? 0.50 0.80 db f = 2.5 to 3.0 ghz ? 0.65 ? db isolation isl rfc to rf1, 2, 3 f = 0.5 to 1.0 ghz 22.5 25.5 ? db (off) f = 1.0 to 2.0 ghz 16.5 19.5 ? db f = 2.0 to 2.5 ghz 14.5 17.5 ? db f = 2.5 to 3.0 ghz ? 15.5 ? db return loss (rfc) rl c f = 0.5 to 3.0 ghz 15 20 ? db return loss (rf1, 2, 3) rl1, 2, 3 f = 0.5 to 3.0 ghz 15 20 ? db 0.1 db loss compression p in (0.1 db) rfc to rf1, 2, 3 f = 2.5 ghz +19.0 +22.0 ? dbm input power note 1 1 db loss compression p in (1 db) rfc to rf1, 2, 3 f = 2.5 ghz +21.0 +25.0 ? dbm input power note 2 2nd harmonics 2f0 f = 2.5 ghz, p in = 17 dbm ? 75 ? dbc 3rd harmonics 3f0 f = 2.5 ghz, p in = 17 dbm ? 75 ? dbc switch control current i cont no rf input ? 0.1 5.0 a switch control speed t sw 50% ctl to 90/10% rf ? 50 ? ns notes: 1. p in (0.1 db) is the measured input power level when the insert ion loss increases 0.1 db more than that of the linear range. 2. p in (1 db) is the measured input power level when the inserti on loss increases 1 db more than that of the linear range. caution it is necessary to use dc blocking capacitors with this device. free datasheet http:///
pg2413t6z r09ds0001ej0100 rev.1.00 page 5 of 11 may 20, 2010 evaluation circuit 1 2 3 v cont 1 8 7 6 1 000 pf rfc 56 pf v cont 2 v cont 3 4 rf1 56 pf 5 rf2 56 pf 1 000 pf 1 000 pf rf3 56 pf the application circuits and their parameters are for refere nce only and are not intended for use in actual design-ins. application information l esd c b c b c b switch ? c b are dc blocking capacitors external to the device. a value of 56 pf is sufficient for operation from 500 mhz to 2.5 ghz bands. the value may be tailored to provide specific electrical responses. ? the rf ground connections should be kept as short as possible and connected to directly to a good rf ground for best performance. ? l esd provides a means to increase the esd protection on a sp ecific rf port, typically the port attached to the antenna. free datasheet http:///
pg2413t6z r09ds0001ej0100 rev.1.00 page 6 of 11 may 20, 2010 typical characteristics ( t a = +25 c, dc blocking capacitors = 56 pf, unless otherwise specified ) insertion loss l ins (db) frequency f (ghz) rfc-rf1/rf2/rf3 insertion loss vs. frequency ?0.1 ?0.3 ?0.7 1.5 3.0 0.5 1.0 2.0 2.5 0.0 ?0.2 ?0.4 ?0.5 v cont (h) = 3.0 v isolation isl (db) frequency f (ghz) rfc-rf1/rf2/rf3 isolation vs. frequency 0 ?5 ?10 ?15 ?20 ?25 ?30 ?35 ?40 1.5 3.0 0.5 1.0 2.0 2.5 0.0 3.0 v v cont (h) = 1.8 v return loss (rfc) rl c (db) frequency f (ghz) return loss (rfc) vs. frequency 1.5 3.0 0.5 1.0 2.0 2.5 0.0 v cont (h) = 3.0 v 1.8 v insertion loss l ins (db) switch control voltage (h) v cont (h) (v) rfc-rf1/rf2/rf3 insertion loss vs. switch control voltage (h) 3.0 4.0 2.0 2.5 3.5 1.5 f = 1.0 ghz isolation isl (db) switch control voltage (h) v cont (h) (v) rfc-rf1/rf2/rf3 isolation vs. switch control voltage (h) ?0.6 0 ?5 ?10 ?15 ?20 ?25 ?30 ?35 ?40 ?45 ?50 return loss (rf1, 2, 3) rl1, 2, 3 (db) frequency f (ghz) return loss (rf1, 2, 3) vs. frequency 1.5 3.0 0.5 1.0 2.0 2.5 0.0 v cont (h) = 3.0 v ?0.1 ?0.3 ?0.7 ?0.2 ?0.4 ?0.5 ?0.6 2.5 ghz 3.0 4.0 2.0 2.5 3.5 1.5 f = 2.5 ghz 1.0 ghz 1.8 v 0 ?5 ?10 ?15 ?20 ?25 ?30 ?35 ?40 ?45 ?50 1.8 v 0 ?5 ?10 ?15 ?20 ?25 ?30 ?35 ?40 remark the graphs indicate nominal characteristics. free datasheet http:///
pg2413t6z r09ds0001ej0100 rev.1.00 page 7 of 11 may 20, 2010 insertion loss l ins (db) input power p in (dbm) rfc-rf1/rf2/rf3 insertion loss, i cont vs. input power 0 ?0.5 ?1.0 ?1.5 ?2.0 ?2.5 ?3.0 25 35 20 30 10 v cont (h) = 3.0 v 1.8 v 18 15 12 9 6 3 0 switch control current i cont ( a) f = 2.5 ghz 3.0 v 1.8 v l ins i cont return loss (rfc) rl c (db) return loss (rfc) vs. switch control voltage (h) 0 ?5 ?10 ?15 ?20 ?25 ?30 ?35 ?40 switch control voltage (h) v cont (h) (v) 3.0 4.0 2.0 2.5 3.5 1.5 f = 1.0 ghz 2.5 ghz return loss (rf1, 2, 3) rl1, 2, 3 (db) return loss (rf1, 2, 3) vs. switch control voltage (h) switch control voltage (h) v cont (h) (v) 15 1 db loss compression input power p in (1 db) (dbm) 0.1 db loss compression input power p in (0.1 db) (dbm) switch control voltage (h) v cont (h) (v) rfc-rf1/rf2/rf3 p in (1 db) , p in (0.1 db) vs. switch control voltage (h) 34 32 30 28 26 24 22 20 2.5 4.0 2.0 3.0 1.5 f = 2.5 ghz p in (0.1 db) 3.5 p in (1 db) 0 ?5 ?10 ?15 ?20 ?25 ?30 ?35 ?40 3.0 4.0 2.0 2.5 3.5 1.5 f = 2.5 ghz 1.0 ghz remark the graphs indicate nominal characteristics. free datasheet http:///
pg2413t6z r09ds0001ej0100 rev.1.00 page 8 of 11 may 20, 2010 mounting pad layout dimensions 8-pin plastic tson (unit: mm) 0.7 1.2 8-0.15 1.1 1.7 0.4 remark the mounting pad layout in this document is for reference only. when designing pcb, please consider workability of m ounting, solder joint reliab ility, prevention of solder bridge and so on, in order to optimize the design. free datasheet http:///
pg2413t6z r09ds0001ej0100 rev.1.00 page 9 of 11 may 20, 2010 package dimensions 8-pin plastic tson (unit: mm) a a 0.70.1 (bottom view) (top view) 1.50.1 1.50.1 0.37 +0.03 ?0.05 0.08 min. 0.15 +0.07 ?0.05 0.30.07 (0.24) (side view) 0.40.06 0.20.1 1.20.1 (c0.15) remark a > 0 ( ): reference value free datasheet http:///
pg2413t6z r09ds0001ej0100 rev.1.00 page 10 of 11 may 20, 2010 recommended soldering conditions this product should be soldered and mounted under the following recommended conditions. for soldering methods and conditions other than those recommended below, contact your nearby sales office. soldering method soldering conditions condition symbol infrared reflow peak temperature (package surface temperature) : 260 c or below time at peak temperature : 10 seconds or less time at temperature of 220 c or higher : 60 seconds or less preheating time at 120 to 180 c : 120 30 seconds maximum number of reflow processes : 3 times maximum chlorine content of rosin flux (% mass) : 0.2%(wt.) or below ir260 partial heating peak temperature (terminal temperature) : 350 c or below soldering time (per side of device) : 3 seconds or less maximum chlorine content of rosin flux (% mass) : 0.2%(wt.) or below hs350 caution do not use different soldering methods together (except for partial heating). free datasheet http:///
pg2413t6z r09ds0001ej0100 rev.1.00 page 11 of 11 may 20, 2010 caution gaas products this product uses gallium arsenide (gaas). gaas vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. ? follow related laws and ordinances when disposi ng of the product. if there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. commission a disposal company able to (with a license to) collect, tran sport and dispose of materials that contain arsenic and ot her such industrial waste materials. 2. exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subjec t to special control) up until final disposal. ? do not burn, destroy, cut, crush, or chemically dissolve the product. ? do not lick the product or in any way allow it to enter the mouth. free datasheet http:///
all trademarks and registered trademarks are t he property of their respective owners. c - 1 revision history pg2413t6z data sheet description rev. date page summary 1.00 may 20, 2010 ? first edition issued bluetooth is a trademark owned by bluetooth sig, inc., u.s.a. free datasheet http:///
notice 1. all information included in this document is current as of the date this document is issued. such information, however, is s ubject to change without any prior notice. before purchasing or using any renesas electronics products listed herein, please confirm the latest product information with a renesas electronics sales office. also , please pay regular and careful attention to additional and different information to be disclosed by renesas electronics such as that disclosed through our website. 2. renesas electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property ri ghts of third parties by or arising from the use of renesas electronics products or technical information described in this document. no license, express, implied or otherwise, is granted hereby under any paten ts, copyrights or other intellectual property rights of renesas electronics or others. 3. you should not alter, modify, copy, or otherwise misappropriate any renesas electronics product, whether in whole or in part . 4. descriptions of circuits, software and other related information in this document are provided only to illustrate the operat ion of semiconductor products and application examples. you are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. renesas electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 5. when exporting the products or technology described in this document, you should comply with the applicable export control l aws and regulations and follow the procedures required by such laws and regulations. you should not use renesas electronics products or the technology described in this document for any purpose rela ting to military applications or use by the military, including but not limited to the development of weapons of mass destruction. renesas electronics products and technology may not be used for or incorporate d into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. 6. renesas electronics has used reasonable care in preparing the information included in this document, but renesas electronics does not warrant that such information is error free. renesas electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information incl uded herein. 7. renesas electronics products are classified according to the following three quality grades: "standard", "high quality", an d "specific". the recommended applications for each renesas electronics product depends on the product's quality grade, as indicated below. you must check the quality grade of each renesas electronics produ ct before using it in a particular application. you may not use any renesas electronics product for any application categorized as "specific" without the prior written consent of renesas electronics. fu rther, you may not use any renesas electronics product for any application for which it is not intended without the prior written consent of renesas electronics. renesas electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any renesas electronics product for an application categorized as "specific" or for which the product is not intended wh ere you have failed to obtain the prior written consent of renesas electronics. the quality grade of each renesas electronics product is "standard" unless otherwise expressly specified in a renesas electroni cs data sheets or data books, etc. "standard": computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment ; home electronic appliances; machine tools; personal electronic equipment; and industrial robots. "high quality": transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; safety equipment; and medical equipment not specifically designed for life support. "specific": aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or syst ems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct thr eat to human life. 8. you should use the renesas electronics products described in this document within the range specified by renesas electronics , especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. renesas el ectronics shall have no liability for malfunctions or damages arising out of the use of renesas electronics products beyond such specified ranges. 9. although renesas electronics endeavors to improve the quality and reliability of its products, semiconductor products have s pecific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. further, renesas electronics products are not subject to radiation resistance design . please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a renesas electronics produc t, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measu res. because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 10. please contact a renesas electronics sales office for details as to environmental matters such as the environmental compati bility of each renesas electronics product. please use renesas electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, in cluding without limitation, the eu rohs directive. renesas electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 11. this document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of renes as electronics. 12. please contact a renesas electronics sales office if you have any questions regarding the information contained in this doc ument or renesas electronics products, or if you have any other inquiries. (note 1) "renesas electronics" as used in this document means renesas electronics corporation and also includes its majority-o wned subsidiaries. (note 2) "renesas electronics product(s)" means any product developed or manufactured by or for renesas electronics. http://www.renesas.com refer to "http://www.renesas.com/" for the latest and detailed information. renesas electronics america inc. 2880 scott boulevard santa clara, ca 95050-2554, u.s.a. tel: +1-408-588-6000, fax: +1-408-588-6130 renesas electronics canada limited 1101 nicholson road, newmarket, ontario l3y 9c3, canada tel: +1-905-898-5441, fax: +1-905-898-3220 renesas electronics europe limited dukes meadow, millboard road, bourne end, buckinghamshire, sl8 5fh, u.k tel: +44-1628-585-100, fax: +44-1628-585-900 renesas electronics europe gmbh arcadiastrasse 10, 40472 dsseldorf, germany tel: +49-211-6503-0, fax: +49-211-6503-1327 renesas electronics (china) co., ltd. 7th floor, quantum plaza, no.27 zhichunlu haidian district, beijing 100083, p.r.china tel: +86-10-8235-1155, fax: +86-10-8235-7679 renesas electronics (shanghai) co., ltd. unit 204, 205, azia center, no.1233 lujiazui ring rd., pudong district, shanghai 200120, china tel: +86-21-5877-1818, fax: +86-21-6887-7858 / -7898 renesas electronics hong kong limited unit 1601-1613, 16/f., tower 2, grand century place, 193 prince edward road west, mongkok, kowloon, hong kong tel: +852-2886-9318, fax: +852 2886-9022/9044 renesas electronics taiwan co., ltd. 7f, no. 363 fu shing north road taipei, taiwan, r.o.c. tel: +886-2-8175-9600, fax: +886 2-8175-9670 renesas electronics singapore pte. ltd. 1 harbourfront avenue, #06-10, keppel bay tower, singapore 098632 tel: +65-6213-0200, fax: +65-6278-8001 renesas electronics malaysia sdn.bhd. unit 906, block b, menara amcorp, amcorp trade centre, no. 18, jln persiaran barat, 46050 petaling jaya, selangor darul ehsan, malaysia tel: +60-3-7955-9390, fax: +60-3-7955-9510 renesas electronics korea co., ltd. 11f., samik lavied' or bldg., 720-2 yeoksam-dong, kangnam-ku, seoul 135-080, korea tel: +82-2-558-3737, fax: +82-2-558-5141 sales offices ? 2010 renesas electronics corporation. all rights reserved. colophon 1.0 free datasheet http:///

▲Up To Search▲

Price & Availability of UPG2413T6Z

	To Download UPG2413T6Z Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .